Serving Central Ohio

Superior Solutions, To Protect Your Investment!

Roof Flashing Problems Around Chimneys: What Ohio Homeowners Should Know

October 26, 2026

One of the most common problems Ohio homeowners face is roof flashing issues around chimneys. Flashing is a strip of metal or rubber that creates a watertight seal where the roof meets the chimney. Ohio’s heavy rainfall, high winds, snow, and hail put constant pressure on that seal. If the flashing fails, roof flashing leaks can send water down the chimney and into your attic and ceiling. 

This guide explains how roof flashing problems develop, what signs to watch for, and when to call a professional. At Superior Roof System, we work with homeowners across central Ohio, and roof leaks around chimneys are a common issue we see.

How Chimney Flashing Works

Chimney roof flashing stops water from entering areas where two different materials meet. The roof is made from shingles or panels, which are waterproof. The chimney is made from brick or stone, which is not. The flashing creates a bridge between the two. Proper chimney roof flashing is designed to direct water away from the joint, and a well-planned roof flashing installation is what keeps it working over time.

Most chimney flashing includes the following parts:

  • Base flashing: The section at the bottom of the chimney, attached to the roof deck. It wraps up either side.
  • Step flashing: Individual pieces of metal that run up each side of the chimney. They slot under each row of shingles and overlap one another, directing water down the roof.
  • Counter flashing: The top part of the flashing. It is cut into the mortar joints of the chimney and folded down over the step flashing, forming a lid.
  • Cricket: A small peaked saddle fitted behind wide chimneys, usually wider than 2 feet. It diverts rain and snow.

If any part of the flashing is missing or not fitted properly, it can cause leaks.

Common Roof Flashing Issues Around Chimneys

One home inspector who has written about chimney leaks notes that many chimneys have no counter flashing, or the counter flashing was never set into the mortar joints. Water then gets behind the step flashing, which may be held in place by only a strip of caulking. Many roof flashing problems and chimney flashing issues trace back to installation errors rather than age alone. Other common roof flashing problems include step flashing that is too short, missing, or incorrectly nailed.

Over time, metal corrodes, and mortar joints crack as the chimney expands and contracts. Roof cement or old sealant may hold for a while, but it rarely lasts. Many roof leak around chimney problems start as tiny gaps that grow larger each winter, which is why early attention to flashing damage signs matters.

Signs of Damaged Flashing

Spotting flashing damage signs early can prevent costly roof flashing damage. Watch for:

  • Water staining on ceilings or walls near the chimney, especially after a storm
  • Peeling paint or bubbling wallpaper on the wall behind the chimney
  • Corrosion, rust, or holes in the metal flashing
  • Cracked caulking, sealant, or dry patches
  • Loose metal
  • Crumbling mortar joints where counter flashing should be
  • A damp or musty smell in the attic near the chimney

If you see staining inside but nothing obvious outside, roof flashing problems may be the cause. Masonry can also leak, so it is best to have a professional investigate.

How Ohio Weather Affects Chimney Flashing

Ohio weather can be hard on chimney flashing:

  • Heavy rain: Water can get under the flashing and cause a roof leak around chimney when heavy rain hits the edges.
  • High winds: Wind can loosen metal flashing. High winds during thunderstorms are a common cause of roof leaks around chimneys in late summer and early autumn.
  • Snow and ice: Snow can build up behind the chimney, and ice can work its way under the flashing. Repeated freezing and thawing widens small cracks.
  • Hail: Hail can dent metal flashing and crack the sealant.

Check the flashing before the heavy spring rains and before winter snow.

When to Repair or Replace Flashing

Minor leaks can sometimes be repaired. If there are small gaps in the caulking or sealant, a chimney flashing repair may be possible. However, if the flashing is rusty, bent, or missing, it will usually need replacing. Flashing that was never fitted properly also needs replacing, and a chimney flashing replacement is often the only lasting fix. A roof flashing repair Ohio roofer can assess whether the flashing can be repaired or must be replaced.

Flashing work requires ladders, steep roofs, and cutting into mortar, so it is best left to a professional. Do not try to fix flashing by adding extra sealant. Caulking alone rarely lasts more than a few seasons without proper metalwork.

How We Can Help

We provide custom sheet metal work, including roof flashing installation, valleys, drip edges, and chimney caps. Our sheet metal and guttering solutions are made to fit your chimney and roof precisely, so your flashing is built specifically for your home. Our steep slope roofing team can also inspect how well the flashing works with your shingles or metal panels. If your home has also suffered storm damage, see our storm damage services. You can also learn more about our residential roofing. For Ohio homeowners, we handle roof flashing repair jobs and chimney flashing projects of every size.

Ending Note

Roof flashing problems around chimneys often start small. A missing piece of counter flashing, a crack in the caulking, or a patch of rust can allow water to get in. Checking your chimney after storms and watching for signs of water intrusion can prevent costly roof flashing damage.

If you see water staining around your chimney, call us at (740) 501-1203 or use our contact page to request a free estimate. We can inspect your chimney flashing and recommend the right chimney flashing repair or replacement.

Frequently Asked Questions

1. What causes leaks around chimneys?

Most roof flashing leaks come from missing, rusted, or incorrectly fitted flashing, or from flashing that is held only by caulking. Cracked mortar and problems with the cricket behind wide chimneys can also let water in.

 

2. How do I know if my chimney flashing needs repair?

Look for water staining around the chimney, rusty metal, cracked or peeling sealant, and loose metal. If you see any of these signs, schedule an inspection.\

 

3. Can I repair chimney flashing myself?

Some experienced homeowners can make minor sealant repairs, but flashing work often involves ladders, steep roofs, and cutting into mortar. Done incorrectly, it can make roof flashing leaks worse, so it is best to hire a professional.

 

4. Do you offer emergency chimney leak repairs?

Yes. We offer emergency and weekend appointments. Our main office number is (740) 501-1203, and our emergency number is (330) 298-8192.

 

5. Do you offer free estimates on chimney flashing replacement?

 

Yes. We provide free quotes for our roofing and sheet metal solutions. Call us or request one through our website.

Roof Flashing Problem